Skip to main content


Plugin: python.d.plugin Module: adaptec_raid


This collector monitors Adaptec RAID hardware storage controller metrics about both physical and logical drives.

It uses the arcconf command line utility (from adaptec) to monitor your raid controller.

Executed commands:

  • sudo -n arcconf GETCONFIG 1 LD
  • sudo -n arcconf GETCONFIG 1 PD

This collector is supported on all platforms.

This collector only supports collecting metrics from a single instance of this integration.

The module uses arcconf, which can only be executed by root. It uses sudo and assumes that it is configured such that the netdata user can execute arcconf as root without a password.

Default Behavior


After all the permissions are satisfied, netdata should be to execute commands via the arcconf command line utility


The default configuration for this integration does not impose any limits on data collection.

Performance Impact

The default configuration for this integration is not expected to impose a significant performance impact on the system.


Metrics grouped by scope.

The scope defines the instance that the metric belongs to. An instance is uniquely identified by a set of labels.

Per AdaptecRAID instance

These metrics refer to the entire monitored application.

This scope has no labels.


adaptec_raid.ld_statusa dimension per logical devicebool
adaptec_raid.pd_statea dimension per physical devicebool
adaptec_raid.smart_warningsa dimension per physical devicecount
adaptec_raid.temperaturea dimension per physical devicecelsius


The following alerts are available:

Alert nameOn metricDescription
adaptec_raid_ld_status adaptec_raid.ld_statuslogical device status is failed or degraded
adaptec_raid_pd_state adaptec_raid.pd_statephysical device state is not online



Grant permissions for netdata, to run arcconf as sudoer

The module uses arcconf, which can only be executed by root. It uses sudo and assumes that it is configured such that the netdata user can execute arcconf as root without a password.

Add to your /etc/sudoers file: which arcconf shows the full path to the binary.

netdata ALL=(root)       NOPASSWD: /path/to/arcconf

Reset Netdata's systemd unit CapabilityBoundingSet (Linux distributions with systemd)

The default CapabilityBoundingSet doesn't allow using sudo, and is quite strict in general. Resetting is not optimal, but a next-best solution given the inability to execute arcconf using sudo.

As root user, do the following:

mkdir /etc/systemd/system/netdata.service.d
echo -e '[Service]\nCapabilityBoundingSet=~' | tee /etc/systemd/system/netdata.service.d/unset-capability-bounding-set.conf
systemctl daemon-reload
systemctl restart netdata.service



The configuration file name for this integration is python.d/adaptec_raid.conf.

You can edit the configuration file using the edit-config script from the Netdata config directory.

cd /etc/netdata 2>/dev/null || cd /opt/netdata/etc/netdata
sudo ./edit-config python.d/adaptec_raid.conf


There are 2 sections:

  • Global variables
  • One or more JOBS that can define multiple different instances to monitor.

The following options can be defined globally: priority, penalty, autodetection_retry, update_every, but can also be defined per JOB to override the global values.

Additionally, the following collapsed table contains all the options that can be configured inside a JOB definition.

Every configuration JOB starts with a job_name value which will appear in the dashboard, unless a name parameter is specified.

Config options
update_everySets the default data collection frequency.5no
priorityControls the order of charts at the netdata dashboard.60000no
autodetection_retrySets the job re-check interval in seconds.0no
penaltyIndicates whether to apply penalty to update_every in case of failures.yesno



A basic example configuration per job

name: my_job_name
update_every: 1 # the JOB's data collection frequency
priority: 60000 # the JOB's order on the dashboard
penalty: yes # the JOB's penalty
autodetection_retry: 0 # the JOB's re-check interval in seconds


Debug Mode

To troubleshoot issues with the adaptec_raid collector, run the python.d.plugin with the debug option enabled. The output should give you clues as to why the collector isn't working.

  • Navigate to the plugins.d directory, usually at /usr/libexec/netdata/plugins.d/. If that's not the case on your system, open netdata.conf and look for the plugins setting under [directories].

    cd /usr/libexec/netdata/plugins.d/
  • Switch to the netdata user.

    sudo -u netdata -s
  • Run the python.d.plugin to debug the collector:

    ./python.d.plugin adaptec_raid debug trace

Do you have any feedback for this page? If so, you can open a new issue on our netdata/learn repository.