Skip to main content

APC UPS

Plugin: charts.d.plugin Module: apcupsd

Overview

Monitor APC UPS performance with Netdata for optimal uninterruptible power supply operations. Enhance your power supply reliability with real-time APC UPS metrics.

The collector uses the apcaccess tool to contact the apcupsd daemon and get the APC UPS statistics.

This collector is supported on all platforms.

This collector only supports collecting metrics from a single instance of this integration.

Default Behavior

Auto-Detection

By default, with no configuration provided, the collector will try to contact 127.0.0.1:3551 with using the apcaccess utility.

Limits

The default configuration for this integration does not impose any limits on data collection.

Performance Impact

The default configuration for this integration is not expected to impose a significant performance impact on the system.

Metrics

Metrics grouped by scope.

The scope defines the instance that the metric belongs to. An instance is uniquely identified by a set of labels.

Per ups

Metrics related to UPS. Each UPS provides its own set of the following metrics.

This scope has no labels.

Metrics:

MetricDimensionsUnit
apcupsd.chargechargepercentage
apcupsd.battery.voltagevoltage, nominalVolts
apcupsd.input.voltagevoltage, min, maxVolts
apcupsd.output.voltageabsolute, nominalVolts
apcupsd.input.frequencyfrequencyHz
apcupsd.loadloadpercentage
apcupsd.load_usageloadWatts
apcupsd.temperaturetempCelsius
apcupsd.timetimeMinutes
apcupsd.onlineonlineboolean
apcupsd.selftestOK, NO, BT, NGstatus
apcupsd.statusONLINE, ONBATT, OVERLOAD, LOWBATT, REPLACEBATT, NOBATT, SLAVE, SLAVEDOWN, COMMLOST, CAL, TRIM, BOOST, SHUTTING_DOWNstatus

Alerts

The following alerts are available:

Alert nameOn metricDescription
apcupsd_ups_charge apcupsd.chargeaverage UPS charge over the last minute
apcupsd_10min_ups_load apcupsd.loadaverage UPS load over the last 10 minutes
apcupsd_last_collected_secs apcupsd.loadnumber of seconds since the last successful data collection
apcupsd_selftest_warning apcupsd.selftestself-test failed due to insufficient battery capacity or due to overload.
apcupsd_status_onbatt apcupsd.statusAPC UPS has switched to battery power because the input power has failed
apcupsd_status_overload apcupsd.statusAPC UPS is overloaded and cannot supply enough power to the load
apcupsd_status_lowbatt apcupsd.statusAPC UPS battery is low and needs to be recharged
apcupsd_status_replacebatt apcupsd.statusAPC UPS battery has reached the end of its lifespan and needs to be replaced
apcupsd_status_nobatt apcupsd.statusAPC UPS has no battery
apcupsd_status_commlost apcupsd.statusAPC UPS communication link is lost

Setup

Prerequisites

Install charts.d plugin

If using our official native DEB/RPM packages, make sure netdata-plugin-chartsd is installed.

Required software

Make sure the apcaccess and apcupsd are installed and running.

Configuration

File

The configuration file name for this integration is charts.d/apcupsd.conf.

You can edit the configuration file using the edit-config script from the Netdata config directory.

cd /etc/netdata 2>/dev/null || cd /opt/netdata/etc/netdata
sudo ./edit-config charts.d/apcupsd.conf

Options

The config file is sourced by the charts.d plugin. It's a standard bash file.

The following collapsed table contains all the options that can be configured for the apcupsd collector.

Config options
NameDescriptionDefaultRequired
apcupsd_sourcesThis is an array of apcupsd sources. You can have multiple entries there. Please refer to the example below on how to set it.127.0.0.1:3551no
apcupsd_timeoutHow long to wait for apcupsd to respond.3no
apcupsd_update_everyThe data collection frequency. If unset, will inherit the netdata update frequency.1no
apcupsd_priorityThe charts priority on the dashboard.90000no
apcupsd_retriesThe number of retries to do in case of failure before disabling the collector.10no

Examples

Multiple apcupsd sources

Specify a multiple apcupsd sources along with a custom update interval

# add all your APC UPSes in this array - uncomment it too
declare -A apcupsd_sources=(
["local"]="127.0.0.1:3551",
["remote"]="1.2.3.4:3551"
)

# how long to wait for apcupsd to respond
#apcupsd_timeout=3

# the data collection frequency
# if unset, will inherit the netdata update frequency
apcupsd_update_every=5

# the charts priority on the dashboard
#apcupsd_priority=90000

# the number of retries to do in case of failure
# before disabling the module
#apcupsd_retries=10

Troubleshooting

Debug Mode

To troubleshoot issues with the apcupsd collector, run the charts.d.plugin with the debug option enabled. The output should give you clues as to why the collector isn't working.

  • Navigate to the plugins.d directory, usually at /usr/libexec/netdata/plugins.d/. If that's not the case on your system, open netdata.conf and look for the plugins setting under [directories].

    cd /usr/libexec/netdata/plugins.d/
  • Switch to the netdata user.

    sudo -u netdata -s
  • Run the charts.d.plugin to debug the collector:

    ./charts.d.plugin debug 1 apcupsd

Do you have any feedback for this page? If so, you can open a new issue on our netdata/learn repository.